• <tt id="ykbsp"><address id="ykbsp"><input id="ykbsp"></input></address></tt>
    1. <i id="ykbsp"><sub id="ykbsp"></sub></i>

          CONTACT US    

          Nantong JunHai Machinery Tech. Co., Ltd.
          Address: Taoyuan Town, Rugao City, Jiangsu Province High-tech Industrial Park
          Zip Code:226400
          TEL:+86 18912208346(Mr Tony)

                    +86 13646196569,

                   +86 0513-88541237
          FAX: +86 0513-88541237 / 88541236
          E-mail:ntjhjx@163.com
          Q Q: 1404732482

          MSN:  ntjhjx@live.com

          NEWS

          How to control the noise
           

          National transportation infrastructure, city construction scale is more and more big, the scale, the power in construction is more and more big, traction speed more and more quickly, the key transmission accordingly hoist a drum open gear pair structure size bigger, noise hoist in operation, high speed and high power increasingly, however, this is not allowed by the national standard. Building hoist the national standard GB1955 - 2002 provisions hoist noise qualified limits for machine shall not be greater than 85dB (A), the operator shall not be greater than 88dB (A) ears. When the traction force is small, low speed when the noise is far less than the standard limit, easy control; but when the traction speed is higher, traction force to ensure that the noise does not exceed the standard, effective measures should be taken from the aspects of design, technology, materials, quality inspection etc..

          1 存在問題:卷揚機噪聲來源有多種途徑,但本質上是撞擊和振動的結果,一般是由于齒輪嚙合質量差、運動不平穩在運動中產生了瞬時加速度而造成的。 我公司生產的卷揚機噪聲一般在標準范圍以內,但出現偶爾噪聲超標現象。在排除噪聲時感到無從下手,因機器制造所依據的圖樣、工藝流程相同,既然絕大多數產品合格,就應排除設計和工藝不合理因素。

          1 problems: the noise sources in various ways, but the essence is the impact and vibration results, is generally caused by gear meshing quality is poor, the unstable movement in motion produced transient acceleration. The noise produced by our company is generally in the standard range, but occasionally noise exceed the standard phenomenon. Unable to gain the upper hand in eliminating noise, drawings, process flow on the basis for machine manufacturing the same, since the vast majority of products qualified, it should eliminate the unreasonable factors in design and technology.

          噪聲來源分析及控制

          Noise analysis and control of the source

          1、底盤 我們認為底盤的設計制造存在造成噪聲的可能:①底盤采用箱形結構,不是所有焊縫都進行連續焊接,各個底盤焊縫的長短、高低位置不同,底盤剛性存在較大個體差異,有的則產生共鳴效應,機器如有一點震動噪聲就被放大;②底盤由鋼板焊成,不具備吸震消聲功能,如果其固有頻率與齒輪嚙合頻率接近就可能造成個別機器因齒輪弱小震動引發較大共震,引起噪聲值上升。 我們針對上述可能性分別進行試驗,但通過三次實驗發現噪聲高低與底盤結構、剛度、頻率等因素呈弱相關,噪聲大小與運動件強相關,因此底盤設計構造、制造質量并不是噪聲超標的原因。

          1, we consider the design and manufacture of chassis chassis cause noise may be: ① chassis adopts box type structure, not all welds are continuous welding, various chassis weld length, height, there are great individual differences in the chassis rigidity, others produce resonance effect, the machine such as a little vibration noise is magnified; the chassis is composed of steel plate welded, does not have the shock-absorbing silencing function, if is close to the natural frequency and the gear mesh frequency may cause individual machines for gear weak vibration lead to greater resonance, noise caused by increased. The possibilities are tested, but by three experiments showed a weak correlation factors of noise level and the chassis structure, stiffness, frequency, noise and the size of the moving parts strongly correlated, so the chassis structural design, manufacturing quality and not exceed the standard of noise.

          2、軸承間隙 有人認為,既然噪聲是伴隨卷筒總成和傳動件,那么就可能由于卷筒滑動軸承間隙大而引起。我們對卷筒零件配合間隙進行選擇,保證軸承孔與主軸間隙符合圖紙要求,裝配后進行試驗。試驗時采用變頻電機調速,觀察速度對噪聲的影響。大量試驗結果表明,速度對噪聲影響是第一位的,卷筒轉速越高則噪聲值越大、機器震動越激烈;間隙在其次,主軸與軸套間隙越大則噪聲也越大;而底盤對噪聲影響最小。如果機器本來噪聲就很低,則速度高低、主軸間隙大小的變化都不會產生過大噪聲,由此表明噪聲超標也不是由軸承間隙大而引起的。

          2, the bearing clearance is considered, since noise is accompanied by a drum assembly and transmission parts, then most likely caused by the roll bearing clearance. We on the drum parts with the gap of selection, ensure the bearing hole and shaft gap with the requirements of the drawings, assembly test. Test by frequency conversion motor, observed the influence of velocity on noise. The experimental results show that the effect of noise, speed is the first drum speed, higher noise value is greater, the machine vibration is more intense; the gap in the second, main shaft and the shaft sleeve gap the greater the noise is larger; while the chassis of the lowest noise. If the machine was very low noise, changes in speed, spindle gap size is not too large noise, the noise exceed the standard is not caused by a large bearing clearance.

          Copyright © 2014 Nantong City, Jun Hai Machinery Technology Co., Ltd.Copyright © 2014 Nantong City, Jun Hai Machinery Technology Co., Ltd.
          人妻av中文字幕_中文字幕av一区中文字幕天堂_在线观看日本亚洲一区_亚洲国片精品中文乱码AV